• 质量第一,顾客至上
  • 诚信于天下
  • 携手共创辉煌
首页 >新闻动态 >> 造型机注意事项
造型机注意事项

造型机注意事项
Matters needing attention in molding machine
造型机是一种常见的铸造机械设备。造型机使用时,要注意它的操作要点,保证工作中的安全使用。很多人对造型机使用不是很了解,认为只要投入使用,能够正常运作就好了。正确安全地使用造型机,能够延长造型机的工作寿命,提高生产质量。造型机安全操作的要点如下:
Molding machine is a common casting machinery and equipment. When using the molding machine, we should pay attention to the key points of its operation and ensure the safe use in the work. Many people are not very familiar with the use of molding machine, think that as long as put into use, can operate properly. Using the molding machine correctly and safely can prolong the working life of the molding machine and improve the production quality. The key points for safe operation of the molding machine are as follows:
1、造型机使用时,操作者应熟悉造型机的机械部件、电器部件、动作程序、润滑系统等情况,以及设备使用中规定的其它要求。
1. When using the moulding machine, the operator should be familiar with the moulding machine's mechanical parts, electrical components, action procedures, lubrication system and other requirements stipulated in the use of equipment.
造型机紧实砂型程序4个步骤:振实、压头摆入、压实、压头摆出。
Molding machine compact sand mold program 4 steps: compaction, pressure head swing, compaction, pressure head put out.
造型机起模程序:工作台夹紧、起模杆升起、运走砂箱、机箱部复位。
The molding process of the molding machine is as follows: the worktable is clamped, the lifting rod rises, the sand box is transported, and the cabinet part is reset.
2、造型机使用时,开动设备前,应先检查造型机的润滑装置是否完善,并按规定加油,检查各紧部件是否紧固,各操作手柄是否处于零位(空位),气阀动作是否灵活,管路有无漏气,然后打开总气阀放掉管路中的积气和积水。
2. When the molding machine is used, the lubrication device of the molding machine should be checked before starting the equipment, and refueling according to the regulations to check whether the fastening parts are tightened, whether the operating handle is at zero position (vacancy), whether the valve action is flexible, whether there is air leakage in the pipeline, and then open the main valve to release the gas and water accumulation in the pipeline. .
3、严禁开空车,必须在有载荷的情况下进行试车,检查各工作状态是否正常,对应该加油的地方进行加油润滑。试车正常后方可进行工作。
3. It is strictly forbidden to drive an empty car. It must be tested under the condition of load to check whether the working state is normal or not and to lubricate the place where the oil should be refueled. The test can be carried out after normal operation.
4、造型机使用时要认真观察运转情况,在操作中应经常用空气吹净润滑部位和运转部位的砂粒,严禁各润滑部位粘砂。
4. When using the moulding machine, we should observe the operation carefully. During the operation, we should often use air to blow away the sand particles in the lubricating parts and the running parts, and strictly prohibit the sand sticking in the lubricating parts.
5、造型机使用时,开闭手柄气阀时动作要平稳。
5. When molding machine is used, the movement of the valve should be steady when opening and closing the handle.
6、每完成一次造型工作后要将工作台清理干净,才能进行第二次造型工作的开始。
6. Clean up the workbench after every modeling work, and then start the second modeling work.
7、造型机使用完毕后,要将手柄回到零(空)位,关闭各阀门,清扫设备,打扫现场,要保持设备各滑动(转动)部位的清洁和润滑,认真收检工具,模具。
7. After the molding machine is finished, it is necessary to return the handle to zero (empty) position, close the valves, clean the equipment, clean the site, to keep the equipment sliding (rotating) parts of the cleaning and lubrication, carefully check the tools, molds.

网站建设:保定遨游公司 版权©保定威利德铸造机械 主营:造型机,树脂砂生产线,自动造型机,铸造机械,铸造设备,造型机厂,造型线等.技术知识
手机:13930206675 电话:0312-3229987 联系人:杨经理 网址:http://www.zaoxingji.com.cn 友链:启闭机
保定网站建设及优化保定遨游网络公司